Full Firmware Scatter Samsung SM-A226BXXS8DWK2 / U8 / S8 .. Dead Boot Repair
Note: After Flashing This Firmware phone will reboot to Download mode, Just U need to flash Full Firmware 4 Files Same Security Level BIT U8 / S8..
This Firmware Only Repair Dead Phones Via USB , Without TP or Opening Phones..
- File No Refund
=========
Testing Flash Sucess:
Platform: MTK SmartPhone - MT65/67/68/81/83/87 | Helio G/P/X
Wait...
[+] Update PMT [re-Part]
[-] Checksum Verify
[+] Safe Erase [Upgrade]
[+] Check compatibility
[+] Backup
[-] UserData Safe
[-] FLASH ERASE
Files: 28
[FL]: E:\GEM Flash\Not Upload\MT6833_samsung_SM-A226BXXS8DWK2_ Dead_Boot_Repair_Scatter\
[FL]: Set: preloader_s96801aa2.bin
[FL]: Set: spmfw.img
[FL]: Set: tinysys-scp.bin
[FL]: Set: sspm.img
[FL]: Set: tz.img
[FL]: Set: tzar.img
[FL]: Set: gz.img
[FL]: Set: lk.bin
[FL]: Set: dpm.img
[FL]: Set: mcupm.img
[FL]: Set: dtbo.img
[FL]: Set: vbmeta.img
[FL]: Set: md1rom.img
[FL]: Set: pi_img.img
[FL]: Set: logo.bin
[FL]: Set: param.img
[FL]: Set: up_param.img
[FL]: Set: boot.img
[FL]: Set: recovery.img
[FL]: Set: vbmeta_system.img
[FL]: Set: vbmeta_vendor.img
[FL]: Set: efuse.img
[FL]: Set: super.img
[FL]: Set: prism.img
[FL]: Set: optics.img
[FL]: Set: cache.img
[FL]: Set: omr.img
[FL]: Set: userdata.img
[FL]: Total size: 0x1CEE4899C [ 7.23 GB ]
1. Power Off the device
2. Wait 20 seconds
3. Connect USB cable to device [remember Vol+ | Vol-]
Waiting for device connection...
PTFN: MediaTek PreLoader USB VCOM_V1633 (Android) (COM4)
MODE: PRELOADER PORT; PORT: 4
Waiting BOOT ack...
PRELOADER: ACK confirmed
BROM: Init BROM
BROM: Init passed
CHIP: MT6833 SBID: 0x8A00 HWVR: 0xCA00 SWVR: 0x0000 EVOL: 0x0000 HWC: 0x0989
CODE: Palmer
TYPE: MODERN [RAPHAEL]
BROM: Sec Level: 0x00000005 Mode: SBC+SDA
BROM: BROM|BL : 0xFF|0x03 [PRELOADER PORT]
AGENT: 0_base: base_v2216 | Manual: Off
[3365c4d2] C:\InfinityBox\CM2MT2\boot\0_base\base_v2216\MTK_AllInOne_DA.bin
[14f3cf66] E:\GEM Flash\Not Upload\MT6833_samsung_SM-A226BXXS8DWK2_ Dead_Boot_Repair_Scatter\preloader_s96801aa2.bin
Looking for suitable BootChain in DA...
Found MT6833
AGENT: MTK_DOWNLOAD_AGENT
BROM: Sending 1st DA...
BROM: Reset Interface
PTFN: USB Serial Device (COM36)
MODE: BOOTROM; PORT: 36
Waiting BOOT ack...
BROM: Skip ACK verify
BROM: Init BROM
BROM: Init passed
CHIP: MT6833 SBID: 0x8A00 HWVR: 0xCA00 SWVR: 0x0000 EVOL: 0x0000 HWC: 0x0989
CODE: Palmer
TYPE: MODERN [RAPHAEL]
MEID: A3329AD8FA1E994D25D353429B2AD36C
BROM: Sec Level: 0x000000E5 Mode: SBC+SDA+EXT
BROM: BROM|BL : 0x05|0xFE [BOOTROM]
BROM: SOCID: 0A89135FA106343070EBCFCBA020AB98AEEE66872C236436044318EA372BE874
BROM: SLA: Local Auth
BROM: SLA: Starting Auth
BROM: SLA: Auth Passed
BROM: SEC: 0x000000E0
AGENT: 0_base: base_v2216 | Manual: Off
[3365c4d2] C:\InfinityBox\CM2MT2\boot\0_base\base_v2216\MTK_AllInOne_DA.bin
[14f3cf66] E:\GEM Flash\Not Upload\MT6833_samsung_SM-A226BXXS8DWK2_ Dead_Boot_Repair_Scatter\preloader_s96801aa2.bin
Looking for suitable BootChain in DA...
Found MT6833
AGENT: MTK_DOWNLOAD_AGENT
BROM: Sending 1st DA...
BROM: DA sent
BROM: Transfer control to DA...
DA: AGENT started
DA: SYNC
DA: MODE: BROM
DA: EXT_RAM NOT initialized
EMMC:
CID: 1501004448364441420051F76AF87837
VEN: Samsung OEM: 0 ID: 444836444142 [DH6DAB] PRV: 0x00
SNN: 1375169272 [0x51F76AF8] MF: 7/2021
EMI: MT6752 preloader_s96801aa2.bin with 12 memory type(s) supported
[00] eMMC LP_DDR4X ID: 150100444836444142 Ven: Samsung | Dev: DH6DAB RAM: [ 4.00 GB ]
[01] eMMC LP_DDR4X ID: 13014E47314A395238 Ven: Micron | Dev: G1J9R8 RAM: [ 4.00 GB ]
[02] eMMC LP_DDR4X ID: 150100445036444142 Ven: Samsung | Dev: DP6DAB RAM: [ 4.00 GB ]
[03] eMMC LP_DDR4X ID: 150100445636444142 Ven: Samsung | Dev: DV6DAB RAM: [ 4.00 GB ]
[04] eMMC LP_DDR4X ID: 150100335636434142 Ven: Samsung | Dev: 3V6CAB RAM: [ 6.00 GB ]
[05] eMMC LP_DDR4X ID: 150100335636434D42 Ven: Samsung | Dev: 3V6CMB RAM: [ 6.00 GB ]
[06] eMMC LP_DDR4X ID: 150100445636444D42 Ven: Samsung | Dev: DV6DMB RAM: [ 4.00 GB ]
[07] eMMC LP_DDR4X ID: 13014E47314331324C Ven: Micron | Dev: G1C12L RAM: [ 8.00 GB ]
[08] eMMC LP_DDR4X ID: 150100444336444D42 Ven: Samsung | Dev: DC6DMB RAM: [ 4.00 GB ]
[09] eMMC LP_DDR4X ID: 150100445636444242 Ven: Samsung | Dev: DV6DBB RAM: [ 4.00 GB ]
[0A] eMMC LP_DDR4X ID: 150100335636434242 Ven: Samsung | Dev: 3V6CBB RAM: [ 6.00 GB ]
[0B] eMMC LP_DDR4X ID: 13014E473243323135 Ven: Micron | Dev: G2C215 RAM: [ 8.00 GB ]
EMI: Init EMI from PRELOADER
EMI: EXT_RAM CFG Passed
DA: BOOT to 2nd DA...
DA: 2ND stage confirmed
DA: SYNC with DA passed
DA: Receiving HW info
SRAM: 0x00070000 [ 448.00 KB ]
DRAM: 0x100000000 [ 4.00 GB ]
EMMC:
CID: 1501004448364441420051F76AF87837
VEN: Samsung OEM: 0 ID: 444836444142 [DH6DAB] PRV: 0x00
SNN: 1375169272 [0x51F76AF8] MF: 7/2021
BOOT1: 0x00400000 [ 4.00 MB ]
BOOT2: 0x00400000 [ 4.00 MB ]
RPMB: 0x01000000 [ 16.00 MB ]
USER: 0xE8F800000 [ 58.24 GB ]
CHIP: MT6833 SBID: 0x8A00 HWVR: 0xCA00 SWVR: 0x0001 EVOL: 0x0000 HWC: 0x0989
CODE: Palmer
TYPE: MODERN [RAPHAEL]
RNID: FD086B48A1827C094B3A9A35E873E631
MEID: A3329AD8FA1E994D25D353429B2AD36C
DA: USB: HIGH-SPEED
Boot done [1]
[FL]: HW verification passed
Reading...
Ok
Verify device config...
Ok
Loaders Ok
[FL]: Pre-Flash backup
Backup exist: C:\InfinityBox\CM2MT2\backup\MT6833__A3329AD8FA1E994D25D353429B2AD36C
[FL]: Pre-Flash backup passed
[FL]: Pre-Erase
Erase: 0x0000000000000000 0x0000000000400000
Erase: 0x0000000001800000 0x0000000004000000
Erase: 0x0000000006800000 0x0000000000800000
Erase: 0x000000000B000000 0x0000000002710000
Erase: 0x0000000015C00000 0x0000000008400000
Erase: 0x000000001E380000 0x00000000121A0000
Erase: 0x0000000030800000 0x00000001ED200000
Erase: 0x0000000220C00000 0x00000000C0000000
[FL]: RePartition
[FL]: RePartition Ok
[FL]: Flashing now...
Write: PRELOADER
Update bootloader backup copy...
Update bootloader backup copy Ok
Write: SPMFW
Write: SCP1
Write: SSPM_1
Write: TEE1
Write: TZAR
Write: GZ1
Write: LK
Write: DPM_1
Write: MCUPM_1
Write: DTBO
Write: VBMETA
Write: MD1IMG
Write: PI_IMG
Write: LOGO
Write: PARAM
Write: UP_PARAM
Write: BOOT
Write: RECOVERY
Write: VBMETA_SYSTEM
Write: VBMETA_VENDOR
Write: EFUSE
Write: SUPER
Write: PRISM
Write: OPTICS
Write: CACHE
Write: OMR
Write: USERDATA
[FL]: RePartition
[FL]: RePartition Ok
[FL]: Flashing finished
Done: 00:05:03
Reconnect Power/Cable now
